Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to professional auto locksmiths who have the proper equipment and know-how. They can design and program keys faster and cheaper than dealers.
A dead coin battery is most likely to blame the reason why your key fob isn't locking or unlocking doors. There are also other reasons that the key could be malfunctioning.
Dead Coin Battery
A dead coin battery will prevent your Peugeot 208 from locking or unlocking and cannot start the engine. If this is the scenario, you'll need make use of the backup starting procedure which is explained in the owner's manual to your vehicle.
Another reason the 208 won't start is because the spark plugs have worn down. The spark plugs are responsible for sparking the fuel that ignites the engine. However they have a short life span. They will eventually break down in the event that they aren't utilized enough.
There is a simple solution for this problem. Examine the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. It is also important to clean the battery's contacts in case it is corroded. This can be done by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any corroded parts of the battery. You should then reconnect your cables to connect the positive and negative poles.
Water Damage
If your 208 won't start and the battery is not flat, then you need to make sure that the spark plugs are in good working order. You might find that they are filthy and don't spark. This can be easily corrected by cleaning the spark plugs in an workshop.
Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This makes sure that only the correct key can start the engine. If the chip in the Peugeot key is damaged, it will not send the correct signal to the vehicle.
This is a very common issue that can occur due to water damage. This is a common issue in warmer climates where the vehicle is exposed to snow or rain. In this situation, contact a reliable locksmith who has the required tools and equipment to reprogram the key. They also have the most up-to-date technology and the machinery needed to make a Peugeot 208 smart key. The process shouldn't take more than 15 minutes.
Faulty Battery Contacts
Peugeot replaced the old transponder chips with a brand new type that uses electronic components mounted on a circuitboard. The new system works great when it's new, but the circuit boards deteriorate over time and cease to function properly.
This could prevent the immobiliser from triggering so that your vehicle will not start. Contact an Peugeot specialist or a locksmith if this is the case.
The most frequent issue is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith will replace the battery, and then cut a fresh blade for you. This is a quick solution.
Faulty Receiver Module
It could be that the receiver module is faulty in the event that your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for transmitting radio frequency signals to the on-board computer, which controls the central locking system of your Peugeot vehicle.
Rubber seals on the key fob keep water from getting to the electronic chip. However prolonged exposure to water may penetrate these seals and damage the chip. Submerging the key fob into ocean water on the beach or throwing it into the water can be especially damaging because of the high salt content.
If your Peugeot spare key fob doesn't work it is necessary to have the module replaced. peugeot expert key fob is only completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys like other cars are secured by an immobilizer device. This requires the proper coding to start the car. This is the reason that you should only trust the Peugeot locksmith to design and program an alternative.
Faulty On-Board Computer
The on-board computer of your Peugeot is responsible for many of the functions in your car including power windows and airbags. The on-board computer displays an error code when something goes wrong. The code is stored within the system and stays there until the issue is resolved. Most often, this involves replacing the onboard computer.
One of the main reasons for the airbag light turning on is loose or corroded connectors in the airbag sensor. This could be due to wear and tear, age or exposure to salt and moisture. It is imperative to have this issue addressed as quickly as possible, since an airbag that is not functioning properly could be risky in the event of an accident.
If you find a card not found error on your Peugeot, the key battery inside the key fob might be weak or dead. This will stop the key fob sending a signal to deactivate the immobilizer in your vehicle. Test this by pressing the unlock key on the key fob, and then trying to start your car. If this doesn't work, the key battery has to be replaced.